View AT28C16-15_1069650.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* Fast Read Access Time - 150 ns * Fast Byte Write - 200 s or 1 ms * Self-Timed Byte Write Cycle
- Internal Address and Data Latches - Internal Control Timer - Automatic Clear Before Write Direct Microprocessor Control - DATA POLLING Low Power - 30 mA Active Current - 100 A CMOS Standby Current High Reliability - Endurance: 104 or 105 Cycles - Data Retention: 10 Years 5V 10% Supply CMOS & TTL Compatible Inputs and Outputs JEDEC Approved Byte Wide Pinout Commercial and Industrial Temperature Ranges
* * * * * * *
16K (2K x 8) Parallel EEPROMs AT28C16
Description
The AT28C16 is a low-power, high-performance Electrically Erasable and Programmable Read Only Memory with easy to use features. The AT28C16 is a 16K memory organized as 2,048 words by 8 bits. The device is manufactured with Atmel's reliable (continued) nonvolatile CMOS technology.
Pin Configurations
Pin Name A0 - A10 CE OE WE I/O0 - I/O7 NC DC Function Addresses Chip Enable Output Enable Write Enable Data Inputs/Outputs No Connect Don't Connect PLCC Top View
A7 NC NC DC VCC WE NC A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 GND
PDIP SOIC , Top View
1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC A8 A9 WE OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3
I/O1 I/O2 GND DC I/O3 I/O4 I/O5
14 15 16 17 18 19 20
A6 A5 A4 A3 A2 A1 A0 NC I/O0
5 6 7 8 9 10 11 12 13
4 3 2 1 32 31 30
29 28 27 26 25 24 23 22 21
A8 A9 NC NC OE A10 CE I/O7 I/O6
Note: PLCC package pins 1 and 17 are DON'T CONNECT.
Rev. 0540B-10/98
1
The AT28C16 is accessed like a static RAM for the read or write cycles without the need of external components. During a byte write, the address and data are latched internally, freeing the microprocessor address and data bus for other operations. Following the initiation of a write cycle, the device will go to a busy state and automatically clear and write the latched data using an internal control timer. The end of a write cycle can be determined by DATA POLLING of I/O7. Once the end of a write cycle has been detected, a new access for a read or a write can begin.
The CMOS technology offers fast access times of 150 ns at low power dissipation. When the chip is deselected the standby current is less than 100 A. Atmel's 28C16 has additional features to ensure high quality and manufacturability. The device utilizes error correction internally for extended endurance and for improved data retention characteristics. An extra 32 bytes of EEPROM are available for device identification or tracking.
Block Diagram
Absolute Maximum Ratings*
Temperature Under Bias ................................ -55C to +125C Storage Temperature ..................................... -65C to +150C All Input Voltages (including NC Pins) with Respect to Ground ...................................-0.6V to +6.25V All Output Voltages with Respect to Ground .............................-0.6V to VCC + 0.6V Voltage on OE and A9 with Respect to Ground ...................................-0.6V to +13.5V *NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability
2
AT28C16
AT28C16
Device Operation
READ: The AT28C16 is accessed like a Static RAM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in a high impedance state whenever CE or OE is high. This dual line control gives designers increased flexibility in preventing bus contention. BYTE WRITE: Writing data into the AT28C16 is similar to writing into a Static RAM. A low pulse on the WE or CE input with OE high and CE or WE low (respectively) initiates a byte write. The address location is latched on the last falling edge of WE (or CE); the new data is latched on the first rising edge. Internally, the device performs a selfclear before write. Once a byte write has been started, it will automatically time itself to completion. Once a programming operation has been initiated and for the duration of tWC, a read operation will effectively be a polling operation. FAST BYTE WRITE: The AT28C16E offers a byte write time of 200 s maximum. This feature allows the entire device to be rewritten in 0.4 seconds. DATA POLLING: The AT28C16 provides DATA POLLING to signal the completion of a write cycle. During a write cycle, an attempted read of the data being written results in the complement of that data for I/O7 (the other outputs are indeterminate). When the write cycle is finished, true data appears on all outputs. WRITE PROTECTION: Inadvertent writes to the device are protected against in the following ways: (a) V C C sense--if VCC is below 3.8V (typical) the write function is inhibited; (b) VCC power on delay--once VCC has reached 3.8V the device will automatically time out 5 ms (typical) before allowing a byte write; and (c) write inhibit--holding any one of OE low, CE high or WE high inhibits byte write cycles. CHIP CLEAR: The contents of the entire memory of the AT28C16 may be set to the high state by the CHIP CLEAR operation. By setting CE low and OE to 12 volts, the chip is cleared when a 10 msec low pulse is applied to WE. D E V I C E I DE NT I F I C A T I O N : A n e x t r a 3 2 b y t e s o f EEPROM memory are available to the user for device identification. By raising A9 to 12 0.5V and using address locations 7E0H to 7FFH the additional bytes may be written to or read from in the same manner as the regular memory array.
3
DC and AC Operating Range
AT28C16-15 Operating Temperature (Case) VCC Power Supply Com. Ind. 0C - 70C -40C - 85C 5V 10%
Operating Modes
Mode Read Write
(2)
CE VIL VIL VIH X X X VIL
OE VIL VIH X
(1)
WE VIH VIL X VIH X X VIL
I/O DOUT DIN High Z
Standby/Write Inhibit Write Inhibit Write Inhibit Output Disable Chip Erase Notes: 1. X can be VIL or VIH. 2. Refer to AC Programming Waveforms. 3. VH = 12.0V 0.5V
X VIL VIH VH
(3)
High Z High Z
DC Characteristics
Symbol ILI ILO ISB1 ISB2 Parameter Input Load Current Output Leakage Current VCC Standby Current CMOS VCC Standby Current TTL Condition VIN = 0V to VCC + 1V VI/O = 0V to VCC CE = VCC - 0.3V to VCC + 1.0V Com. CE = 2.0V to VCC + 1.0V f = 5 MHz; IOUT = 0 mA CE = VIL Ind. Com. Ind. Min Max 10 10 100 2 3 30 45 0.8 2.0 IOL = 2.1 mA IOH = -400 A 2.4 .4 Units A A A mA mA mA mA V V V V
ICC VIL VIH VOL VOH
VCC Active Current AC Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage
4
AT28C16
AT28C16
AC Read Characteristics
AT28C16-15 Symbol tACC tCE
(1) (2)
Parameter Address to Output Delay CE to Output Delay OE to Output Delay CE or OE High to Output Float Output Hold from OE, CE or Address, whichever occurred first
Min
Max 150 150
Units ns ns ns ns ns
tOE
10 0 0
70 50
tDF(3)(4) tOH
AC Read Waveforms(1)(2)(3)(4)
Notes:
1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change without impact on tACC. 3. tDF is specified from OE or CE whichever occurs first (CL = 5 pF). 4. This parameter is characterized and is not 100% tested.
Input Test Waveforms and Measurement Level
Output Test Load
tR, tF < 20 ns
Pin Capacitance
f = 1 MHz, T = 25C(1)
Symbol CIN COUT Note: Typ 4 8 Max 6 12 Units pF pF Conditions VIN = 0V VOUT = 0V
1. This parameter is characterized and is not 100% tested.
5
AC Write Characteristics
Symbol tAS, tOES tAH tWP tDS tDH, tOEH tCS, tCH tWC Parameter Address, OE Set-up Time Address Hold Time Write Pulse Width (WE or CE) Data Set-up Time Data, OE Hold Time CE to WE and WE to CE Set-up and Hold Time AT28C16 Write Cycle Time AT28C16E 100 200 Min 10 50 100 50 10 0 0.5 1.0 1000 Typ Max Units ns ns ns ns ns ns ms s
AC Write Waveforms
WE Controlled
CE Controlled
6
AT28C16
AT28C16
Data Polling Characteristics(1)
Symbol tDH tOEH tOE tWR Notes: Parameter Data Hold Time OE Hold Time OE to Output Delay
(2)
Min 10 10
Typ
Max
Units ns ns ns
Write Recovery Time 1. These parameters are characterized and not 100% tested. 2. See AC Characteristics.
0
ns
Data Polling Waveforms
Chip Erase Waveforms
tS = tH = 1 sec (min.) tW = 10 msec (min.) VH = 12.0V 0.5V
7
8
AT28C16
AT28C16
Ordering Information(1)
tACC (ns) 150 ICC (mA) Active 30 Standby 0.1 Ordering Code AT28C16(E)-15JC AT28C16(E)-15PC AT28C16(E)-15SC AT28C16(E)-15JI AT28C16(E)-15PI AT28C16(E)-15SI Package 32J 24P6 24S 32J 24P6 24S Operation Range Commercial (0C to 70C) Industrial (-40C to 85C)
45
0.1
Notes:
1. See Valid Part Numbers table below. 2. The 28C16 200 ns and 250 ns speed selections have been removed from valid selections table and are replaced by the faster 150 ns TAA offering. 3. The 28C16 ceramic package offerings have been removed. New designs should utilize the 28C256 ceramic offerings.
Valid Part Numbers
The following table lists standard Atmel products that can be ordered.
Device Numbers AT28C16 AT28C16E AT28C16 Speed 15 15 Package and Temperature Combinations JC, JI, PC, PI, SC, SI JC, JI, PC, PI, SC, SI W
Die Products
Reference Section: Parallel EEPROM Die Products
Package Type 32J 24P6 24S W 32 Lead, Plastic J-Leaded Chip Carrier (PLCC) 24 Lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) 24 Lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC) Die Options Blank E Standard Device: Endurance = 10K Write Cycles; Write Time = 1 ms
High Endurance Option: Endurance = 100K Write Cycles; Write Time = 200 s
9
Packaging Information
32J, 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters)
JEDEC STANDARD MS-018 AA
24P6, 24-Lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters)
JEDEC STANDARD MS-011 AA
.045(1.14) X 45
PIN NO. 1 IDENTIFY
.025(.635) X 30 - 45 .012(.305) .008(.203) .530(13.5) .490(12.4) .021(.533) .013(.330) .030(.762) .015(3.81) .095(2.41) .060(1.52) .140(3.56) .120(3.05)
1.27(32.3) 1.24(31.5)
PIN 1
.032(.813) .026(.660)
.553(14.0) .547(13.9) .595(15.1) .585(14.9)
.566(14.4) .530(13.5)
.050(1.27) TYP
1.100(27.94) REF .220(5.59) MAX SEATING PLANE .161(4.09) .125(3.18) .110(2.79) .090(2.29) .065(1.65) .041(1.04) .630(16.0) .590(15.0) 0 REF 15 .690(17.5) .610(15.5)
.090(2.29) MAX .005(.127) MIN
.300(7.62) REF .430(10.9) .390(9.90) AT CONTACT POINTS
.065(1.65) .015(.381) .022(.559) .014(.356)
.022(.559) X 45 MAX (3X) .453(11.5) .447(11.4) .495(12.6) .485(12.3)
.012(.305) .008(.203)
24S, 24-Lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC) Dimensions in Inches and (Millimeters)
.020(.508) .013(.330)
.299(7.60) .420(10.7) .291(7.39) .393(9.98) PIN 1 ID
.050(1.27) BSC .616(15.6) .598(15.2)
.105(2.67) .092(2.34)
.012(.305) .003(.076)
.013(.330) .009(.229) 0 REF 8 .050(1.27) .015(.381)
10
AT28C16
AT28C16
11
Atmel Headquarters
Corporate Headquarters
2325 Orchard Parkway San Jose, CA 95131 TEL (408) 441-0311 FAX (408) 487-2600
Atmel Operations
Atmel Colorado Springs
1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL (719) 576-3300 FAX (719) 540-1759
Europe
Atmel U.K., Ltd. Coliseum Business Centre Riverside Way Camberley, Surrey GU15 3YL England TEL (44) 1276-686677 FAX (44) 1276-686697
Atmel Rousset
Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4 42 53 60 00 FAX (33) 4 42 53 60 01
Asia
Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon, Hong Kong TEL (852) 27219778 FAX (852) 27221369
Japan
Atmel Japan K.K. Tonetsu Shinkawa Bldg., 9F 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581
Fax-on-Demand
North America: 1-(800) 292-8635 International: 1-(408) 441-0732
e-mail
literature@atmel.com
Web Site
http://www.atmel.com
BBS
1-(408) 436-4309
(c) Atmel Corporation 1998. Atmel Cor poration makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's website. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual proper ty of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life suppor t devices or systems. Marks bearing
(R)
and/or
TM
are registered trademarks and trademarks of Atmel Corporation. Printed on recycled paper.
0540B-10/98/xM
Terms and product names in this document may be trademarks of others.

▲Up To Search▲

Price & Availability of AT28C16-15

	To Download AT28C16-15 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .